Categories
    ·Colnago
    ·Argon 18
    ·BigBlow
    ·Fulcrum
    ·CeramicSpeed
    ·Pioneer
    ·Easton
    ·Feedback Sports
    ·Lake
    ·Litespeed
    ·Michelin
    ·Selle Italia
    ·Sella Italia

CeramicSpeed 3D Printed Hollow Ti Shimano 11 Speed Pulley Wheels

CeramicSpeed 3D Printed Hollow Ti Shimano 11 Speed Pulley WheelsCeramicSpeed 3D Printed Hollow Ti Shimano 11 Speed Pulley Wheels
click image to enlarge

Description

About CeramicSpeed 3D Printed Hollow Ti Shimano 11 Speed Pulley Wheels

CeramicSpeed delivers unmatched performance in key areas of your bike.

Special edition 3D printed hollow pulley wheels that accommodate all Shimano 11s groupsets, including Shimano 9100-series rear derailleurs. The Pulley Wheels are printed from titanium powder and are fitted with CeramicSpeed Coated Bearings.

A world premiere and technological innovation, these hollow 3D printed titanium pulley wheels are 5-10% lighter than their original titanium Pulley Wheels and guarantee the same unparalleled lifetime and reduced friction.

The combination of 3D printed titanium pulley wheels and coated CeramicSpeed Bearings result in the best pulley wheels in the world. Since the pulley wheels are the fastest spinning bearings on your bike, this CeramicSpeed upgrade is the most effective way to save energy or improve your time.

The 3D printed titanium pulley wheels are extremely resistant to wear. This makes them a great choice if you ride in demanding conditions or just ride a lot. To give even greater protection and reduced friction, a super thin (2 microns) protective coating is applied to the bearing races. This further increases the resistance of the bearing to corrosion or damage from foreign objects.

Installation

To make sure that the Pulley Wheels perform at their best, it is important that your new pulley wheels are mounted correctly. In order to make the most out of your CeramicSpeed Pulley Wheels and enjoy the advantages of low friction and unmatched longevity take a look at this video for step by step mounting instructions.

Maintenance

It is important that you properly lubricate your bearings in order to ensure optimum performance and maximum longevity. Add oil to the outside of the bearing seal, so the oil can penetrate the bearing. Maintenance for your CeramicSpeed Pulley Wheels is recommended every time you lubricate your chain, wash your bike, or after riding in wet or muddy conditions. For further maintenance instructions, please watch this video

Coated bearings

CeramicSpeed's coating has several performance enhancing properties that makes it unique. Thanks to their continuous R&D program, CeramicSpeed have developed a special coating in cooperation with a European coating specialist. Applied to the steel races of the bearing, through an advanced process that ensures an even, smooth and homogeneous surface, the coating formula improves even further the high quality of the CeramicSpeed bearings.

Low friction Once coated, the bearing races deliver a hardness level matched only by the CeramicSpeed balls, providing an extremely low friction coefficient between the two materials. The result is thus even less friction in our coated bearings than in their standard bearings.


Coating Graf Friction - The coating is a metallic layer, which is 75% harder than the hardened steel races. The coating is applied in a very thin and even layer of 3 microns (0,003 mm) on the entire surface of the bearing race. Both the inside and the outside are treated to achieve optimal results. As CeramicSpeed use a metallic coating on top of the hardened steel, it can be difficult to see that a bearing is actually coated. However, if you take a closer look at a coated bearing, you will notice that the surface has a different shine than a standard CeramicSpeed bearing.

Lifetime - The coating has several properties that improve the lifetime of CeramicSpeed's bearings. The increased hardness of the races combined with the super smooth and round CeramicSpeed balls, means virtually no wear on the bearing.

The coating layer is applied completely closed and homogenous. The formula used for the coating is extremely resistant to corrosion. This means that even if the bearing is contaminated with degreaser, water or mud, the risk of bearing failure due to corrosion is negligible.

How to achieve the optimal performance - The coated bearings are more resistant to lack of lubrication when it comes to wear and damage on the bearing nonetheless, this does not mean that the need for maintenance is completely eliminated. Just as CeramicSpeed do with their standard bearings, they recommend to always lubricate them with our special grease to achieve optimal performance in terms of low friction and long lifetime. For all training and racing applications they recommend the use of CeramicSpeed Blue all-round grease. If you want to achieve the lowest possible friction, CeramicSpeed recommend you to use their TT grease. Please be aware that compared to the standard Blue all-round grease, the TT grease has a shortened lifetime and therefore, it requires more frequent application.

Handmade in Denmark Like all other CeramicSpeed bearings, their coated products are handmade in Denmark. This means all bearings are built by hand and inspected manually at each step in the production process. Building a coated bearing adds a number of extra steps to the process. The CeramicSpeed balls and steel races are matched within microns after which, each set of races is coated. The races are kept together in pairs through the entire process and after coating, each set needs to pass the quality control before they go into production.

CeramicSpeed coated bearings are available for pulley wheels, bottom brackets, wheel bearings and the Oversized Pulley Wheel System.

What's In The Box

2 pulley wheels 

Spacers 

Oil 

Sticker sheet

More About The Manufacturer CeramicSpeed

CeramicSpeed is one of the world’s leading suppliers of ceramic bearings. As the first ones to introduce ceramic bearings to the cycling industry, CeramicSpeed has grown rapidly, focusing on cycling and industrial applications. They have more than 15 years experience in bearings applications, and have developed close relationships with their component suppliers over the years – each of whom is the very best in their field.